Products used in the frequently asked questions, I hope to give you help, and more pleasant to use our products

With the rapid development of agricultural mechanization, agricultural tractors, more and more, to adapt to this situation, give full play to the role of the machine, we must grasp the main points of the proper use of tractors.

1, start according to the test, engine start caused by the wear was about 50% of the total wear -60%, in order to reduce wear, prevent accidents note the following: �� best to use before starting the transfer roll to roll the number of crankshaft 10 turn, long-term without the engine in particular should be done to prevent lubricating oil can not be timely due to flow friction surface and accelerated wear or even bush-burning and other incidents. �� not fully warm the engine, not the supply of fuel, the cylinder wall to prevent erosion and dilution of fuel oil. �� startup accelerator should not be too large to avoid excessive idling speed, accelerating wear.

2, preheat and maintain a normal temperature of engine cooling water to work at low temperatures, due to fuel combustion role of sulfur dioxide and sulfur trioxide, erosion of the cylinder increased significantly, to reduce erosion should note the following points: �� to insulation measures to minimize the engine warm-up time. �� engine should be warm to the temperature reached 40 �� before they start, the water temperature reached 60 �� before loading operation.

3, load tractor should be close to full capacity is not overloaded with work.

4, right in principle, be manipulated to minimize tractor tractor all moving parts may be additional inertia or impact load. That should be sought in the operation running smoothly, not suddenly change speed lever position, do not slam on the clutch, and over the uneven road ditch should be at low speed and so on.

5, Winter Notes on the use of tractors �� In order to facilitate starting the engine, electric starting system on the maintenance should be strengthened, so that the role of a good warm-devices, according to an appropriate increase of the temperature dropped, the proportion of rechargeable batteries, pay attention to insulation and the batteries necessary additional charge. Application of hot water when the engine warm start, and should be heating oil pan and transmission lubricants. �� In order to prevent the engine cooling water temperature is too low, additional insulation should be before the radiator. Should be used within the cooling system for antifreeze, engine fire, the absence of freezing measures, when the water temperature dropped to about 75 �� cooling water when exhausted. �� switching to winter fuel and lubricants. �� to the wet air filter to add appropriate amount of diesel oil to improve the filtration effect. �� strengthening the clutch, brake and control mechanism of the maintenance and inspection to prevent road accidents arising snow and ice. Proper tire inflation pressure should also improve the work after the tractor will not stop water in the wet area so that walking devices freeze on the ground and started walking when the transmission lines to overload.
 

Tractor gearbox failure is mainly due to production shaft, bearings, gears, fork, pin Ding Xiao and springs deformation or wear. If maintenance is not timely or improper operation, lubricant oil surface is too low, oil is not promptly replaced; shift improper operation, gear end damage, the state will result in deterioration of transmission technology.

Press the maintenance and operation method can significantly reduce the transmission failure, extending service life.

(1) always check transmission status of all connected parts of the fastening, if necessary, be tightened. Regular inspection and external engagement shaft seals deal with any oil spill, oil leakage, if necessary, seal failure is more abstract and paper pad, and tighten the screws. Regularly replaced with new oil, oil change, to let hot dirty oil, diesel or kerosene cleaning, the new lubricant should be changed to meet the requirements.

(2) shift, the control lever can not be too much force, so as not to damage the fork to fight tooth and other components. When the clutch is completely separated after the shift, so as not to bash gears. Transport operations, you can not stop shift. Clutch should not be too fast to avoid transmission parts subjected to impact loading, resulting in early tooth surface spalling, surface Jishang spline shaft drive, or even result in a broken flower chain axis. Carried with a fierce clutch pedal is strictly prohibited method to overcome the heavy load or beyond the barriers, to reduce the impact of gear wear.